 |
|
 |
C02 CNTRLR (PPM-3 /CO2 PPM )
| We are currently updating our prices, please call for more information. |
|
The PPM-3 from C.A.P. is the most affordable and simple CO2 controller available. It's proven technology is very accurate at measuring levels of Carbon Dioxide in your growing area from 0 to 5000 ppm (Parts-Per-Million). Using the PPM-3 is quite simple. Just plug your CO2 device (CO2 valve or generator) into the piggyback cord and it will automatically maintain the CO2 level that you specify. The PPM-3 works with any make of CO2 valve or generator that is 120 volt.
702020 |
|
| TOP |
|
 |
CO2 CNTRLR,FUZZY( PPM - 2A )PPM SENSOR
| We are currently updating our prices, please call for more information. |
|
People who need the absolute best CO2 controller available today, use the PPM-2a from C.A.P. What sets the PPM-2a apart from the competition? Fuzzy Logic... Fuzzy Logic can be compared to a good driver. As a good driver approaches a red light, he or she applies the brakes to gradually slow down BEFORE getting to the intersection. Fuzzy Logic(tm) uses the same idea to bring the CO2 level up to the desired setting without over-shooting the desired CO2 level. The PPM-2a automatically dials-in the exact parameters for your area. It learns how your grow area uses CO2 and adapts to keep the CO2 levels constant. The PPM-2a can be connected to a temperature or environmental controller, disabling the CO2 function while your exhaust fans are running to reduce CO2 waste. The PPM-2a is capable of being used to control both compressed CO2 and gas-burning CO2 generators. When used with a CO2 generator, the user can change the PPM-2a mode to ON / OFF control which eliminates the rapid cycling of the CO2 generator. The PPM-2a will control any make of CO2 valve or generator that is 120 volts.
702040 |
|
| TOP |
|
 |
ATMO CNTRLR,( AIR - 2 ) IND T&
| We are currently updating our prices, please call for more information. |
|
Rated for 10 amps @ 120volts. The AIR-2 has the same features as the AIR-1 with the exception of separate temperature and humidity outlets. This allows you to control the temperature and humidity independently. Once you have connected your temperature control device (air conditioner, fan, etc) and a dehumidifier to the AIR-2, your desired temperature and humidity are automatically maintained.
702105 |
|
| TOP |
|
 |
ATMO CNTRLR,( AIR - 3 ) CO2 T&
| We are currently updating our prices, please call for more information. |
|
Rated for 10 amps @ 120volts. The AIR-3 expands our line of atmospheric controllers by providing the ability to coordinate supplemental CO2 with your ventilation equipment. The AIR-3's operation is similar to the AIR-1, with the addition of a photo cell and CO2 outlets. The photo cell ensures that your CO2 device (CO2 valve or generator) only activates when your lights are on. To conserve CO2, the CO2 outlets are automatically disabled while your ventilation equipment is running.
702110 |
|
| TOP |
|
 |
XTRM GH CNTRLR( XGC - 1 ) FUZZ
| We are currently updating our prices, please call for more information. |
|
Control ALL your equipment from ONE compact, reliable controller! The XGC-1 is the best all in one controller ever made. The specifications of the XGC-1 are identical in every way to the CGC-1, except for the addition of Fuzzy Logic™ CO2 control built in! Fuzzy Logic™ can be compared to a good driver. As a good driver approaches a red light, he or she applies the brakes to gradually slow down BEFORE getting to the intersection. Fuzzy Logic™ uses the same idea to keep the CO2 level at your desired setting, without going over the set point.
702125 |
|
| TOP |
|
 |
MASTER LIGHT CNTRLR( MLC - 4 )
| We are currently updating our prices, please call for more information. |
|
Rated at 30 amps @ 240 volts. The MLC-4 Master Lighting Controllers are the best devices for controlling up to four HID lights from one time-clock or controller. You run 30 amp, 240 volt power into the MLC-4, and all of the outlets are controlled by one 120 volt trigger cable. You can plug the trigger cable into a standard 24 hour timer or lighting controller. The MLC-4 features four standard 240 volt style (NEMA 6-15) outlets, which your ballasts are plugged into. An integrated timer option is available which replaces the trigger cable, allowing you to control your MLC with the built-in time clock.
702165 |
|
| TOP |
|
 |
GEN -1 C02 GEN - LP (1 BRNR)
| We are currently updating our prices, please call for more information. |
|
NEW ELECTRONIC IGNITION! The GEN-1 is capable of producing between 3 and 13 cubic feet of CO2 per hour. It comes standard with one burner, producing approximately 3 cubic feet per hour. You can add up to 3 additional burners, increasing the unit is capacity to up approximately 13 cubic feet of CO2 per hour. A Propane Crossover is available which will allow you to connect 2 propane tanks to your generator and run off of either or both tanks.
702250 |
|
| TOP |
|
 |
GEN 2 - CO2 GEN - LP (5 BRNR)
| We are currently updating our prices, please call for more information. |
|
NEW ELECTRONIC IGNITION! The GEN-2 is capable of producing between 16 and 26 cubic feet of CO2 per hour. It comes standard with 5 burners, producing approximately 16 cubic feet of CO2 per hour. You can add up to 3 additional burners, increasing the unit's capacity to up to approximately 26 cubic feet of CO2 per hour. A Propane Crossover is available which will allow you to connect 2 propane tanks to your generator and run off of either or both tanks.
702255 |
|
| TOP |
|
 |
EXPANSION BURNER LP
| We are currently updating our prices, please call for more information. |
|
BNR-1LP: These are our expansion Liquid Propane Burners. Each burner will be individually packaged with an expansion burner, pillow pack of Anti-Seize, Hex wrench for removing cap on manifold and complete installation instructions (Takes less than 2 minutesto install.) BNR-1NG: These are our expansion Natural Gas Burners. Each burner will be individually packaged with an expansion burner, pillow pack of Anti-Seize, Hex wrench for removing cap on manifold and complete installation instructions (Takes less than 2 minutes to install.) LXO -1 Propane Tank Crossover: We offer a simple device called the LXO-1 which allows you to connect your propane CO2 generator to two tanks so when one runs low, it can be changed out without the pilot flame going out. It also doubles the time in between tank changeovers. LPC-1: LP Conversion Kit. This kit will allow the store owner or retail customer to change their Natural Gas Burner to a Liquid Propane Burner. It will come with a LP orifice, LP regulator, and a set of front labels to identify the new unit. NGC-1: Natural Gas Conversion Kit. This kit will allow the store owner or retail customer to change their Liquid Propane Burner to a Natural Gas Burner. It will come with a NG orifice, NG regulator, and a set of front labels to identify the new unit. NOTE: Both of the above kits do NOT include burners. They need to purchase burners separately (BNR-1LP or BNR-1NG). This kit is useful for the store owner so that they do not have to keep both NG and LP generators in stock. They can change one to the other in less than 10 minutes. To keep our competitions generator line in stock, they need 10 units. With our generator, you need 2 units, and a conversion kit!
702270 |
|
| TOP |
|
 |
CROSSOVER VALVE - LP (LXO -1)
| We are currently updating our prices, please call for more information. |
|
BNR-1LP: These are our expansion Liquid Propane Burners. Each burner will be individually packaged with an expansion burner, pillow pack of Anti-Seize, Hex wrench for removing cap on manifold and complete installation instructions (Takes less than 2 minutesto install.) BNR-1NG: These are our expansion Natural Gas Burners. Each burner will be individually packaged with an expansion burner, pillow pack of Anti-Seize, Hex wrench for removing cap on manifold and complete installation instructions (Takes less than 2 minutes to install.) LXO -1 Propane Tank Crossover: We offer a simple device called the LXO-1 which allows you to connect your propane CO2 generator to two tanks so when one runs low, it can be changed out without the pilot flame going out. It also doubles the time in between tank changeovers. LPC-1: LP Conversion Kit. This kit will allow the store owner or retail customer to change their Natural Gas Burner to a Liquid Propane Burner. It will come with a LP orifice, LP regulator, and a set of front labels to identify the new unit. NGC-1: Natural Gas Conversion Kit. This kit will allow the store owner or retail customer to change their Liquid Propane Burner to a Natural Gas Burner. It will come with a NG orifice, NG regulator, and a set of front labels to identify the new unit. NOTE: Both of the above kits do NOT include burners. They need to purchase burners separately (BNR-1LP or BNR-1NG). This kit is useful for the store owner so that they do not have to keep both NG and LP generators in stock. They can change one to the other in less than 10 minutes. To keep our competitions generator line in stock, they need 10 units. With our generator, you need 2 units, and a conversion kit!
702290 |
|
| TOP |
|
|
|
